Online shopping

Bambu Lab A1 3D Printer
Product model BL0085
Brand Bambu Lab
Price 3980 

Quantity

Bambu Lab A1 3D Printer 

*Not Included AMS Lite


Related Article 👉 Bambu Lab A1 Combo 3D Printer Review + Introduction

Product Features

  • Multi-Color Printing
  • Full-auto Calibration
  • Active Flow Rate Compensation
  • 1-Clip Quick Swap Nozzle
  • Active Motor Noise Cancelling
  • 256*256*256 mm³ Build Volume

Multi-Color Printing (With AMS Lite)
The all-new AMS lite is elegant and reliable, making multi-color 3D printing accessible to everyone.


We also provide A1 Combo, please Click Here.

Active Flow Rate Compensation

The A1 revolutionizes flow control in 3D printing. It utilizes a high-resolution, high-frequency eddy current sensor to measure the pressure in the nozzle. Our algorithm actively compensates the flow rate according to the readings to extrude with accuracy.



Full Auto Calibration
The A1 handles various calibrations all by itself. It meticulously calibrates the Z-offset, bed-level, vibration resonance and nozzle pressure for EVERY print job, automatically.





Quick Swap Nozzle
All-new quick swap hotend design, the hotend pops in and out with just 1-Clip.



Active Motor Noise CancellingThe A1 can calibrate paramete
A1 can calibrate parameters to match tiny individual differences between each drive motor. This compensates for the unwanted harshness of motor noise.



Bed Slinger, with CoreXY Speed And Quality
Full-metal rails, rigid frame, nozzle pressure sensor, accelerometers, powerful MCU, and above all, an advanced motion control system that utilizes these features to print a 14-minute benchy with quality and following all the speed benchy rules straight out of the box without using specialized filaments.


Sync with Bambu Studio and Bambu Handy
Remote control and monitor your printer on Bambu Studio or Bambu Handy. Through the built-in camera, you can also record timelapse videos.

 

Full advanced features of A1 3D printers : Learn more

 


See What You Can Do With A1

 

Phone Rig Set - Cage/Filter ring/Handle  【5 HR】

Model created by @Zemister/@plucbernier/@FF3D



Triple-axis Tourbillon  【1.5 DAY】


Mystery Box Model by mcmaven


RC Santa Snowcat  【1 DAY】

Model created by Bambu Lab


Good Vibes Only LightBox  【4.5 HR】

Model created by @braga3dprint

 



   
   Bambu Lab A1                        Spool Holder                        Purge Wiper                           Build Plate     

   
                   PTFE Tube*1             Bambu Filament Samples       Stainless Steel Nozzle              Accessory Box                 

 


Frequently asked questions

 

1. Do you have an official unboxing guide?

A: Yes, please refer to this wiki link for the unboxing video guide.

2. What is the maximum print size of the A1?

A: 256 * 256 *256 mm³. For more details, please check here.

3. What Filaments can A1 Print?

A: 1. Low-temperature filaments such as PLA, PETG, TPU, and support materials for PLA and PETG (Support for PLA, PVA, HIPS, etc.).
2. Conventional high-temperature filaments such as ABS, ASA, PC, PA, PA-CF/GF, PET-CF/GF, PPA-CF/GF, etc.
Kind Reminder:
The standard nozzle is made of stainless steel. When printing filaments containing hard particles (CF, GF, etc.) such as PLA-CF/GF, PLA Glow-in-the-dark, PETG-CF/GF and PAHT-CF/GF, it is necessary to replace the nozzle with hardened steel to prevent excessive wear.
Due to the A1's open-frame design and lower chamber temperature, there is a risk of reduced interlayer strength and increased warping for large-sized models and models with high filling density when using conventional high-temperature filaments such as ABS, ASA, PC, PA, PA-CF/GF, PET-CF/GF, PPA-CF/GF, etc. on the A1. However, these high-temperature filaments can be used on the A1 to print small-sized models with low filling density. The printing results may vary depending on the filaments' dry and wet state, the characteristics of the model itself, printing parameters, and the ambient temperature. For more details, please check here.

4. Is it OK to enclose the A1?

A: We don't recommend enclosing the A1. For more details, please check here.

5. Can you use multiple AMS lite units with the A1 for up to 16 color prints?

A: The A1 can only support one AMS lite, which means it can print with a maximum of 4 colors. For more details, please check here.

 

6. Can I use the AMS on the A1?

A: No, AMS is incompatible with the A1. You must use the AMS lite if you want a multi-color print using A1. For more details, please check here.

 

7. Can AMS lite be mounted on the beam of the A1 to reduce space occupation? If so,how should I proceed with the operation?

A: Please visit our MakerWorld model website, where you will be able to find the model supports, installation tutorial, and purchase links for accessory screws. Additionally, you can also refer to our wiki page for more related information.

For more details, please check here.

8. If I install AMS lite on the beam, will the filament spool slide down, or will it affect the accuracy of vibration compensation?

A: As long as the AMS lite is correctly installed, the filament spool should not slide down, even if the previous two spools have a certain forward tilt angle. Additionally, to avoid affecting the accuracy of vibration compensation, you can add reinforcement to the column. For more details, please check here.

 

Dimensions 385*410*430 mm
Build Volume
256*256*256 mm
Hot End All-Metal 
Extruder Gears Hardened Steel
Nozzle l Max Hot End Temperature: 
Max Hot End Temperature 300℃
Nozzle Diameter (Included) 0.4mm
Nozzle Diameter (Optional) 0.2mm,0.6mm,0.8mm
Filament Cutter Yes
Filament Diameter 1.75 mm
Compatible Build Plate Bambu Textured PEI Plate
Bambu Smooth PEI Plate
Bambu High Temperature Plate (Smooth PEI)
Bambu Cool Plate
Max Build PlateTemperature 100℃
Max Acceleration of Toolhead 500 mm/s
Max Hot End Flow 28 mm³/s @ABS (Model: 150*150 mm single wall; Material: Bambu ABS; Temperature: 280 ℃)
PLA,PETG,TPU, PVA Ideal
ABS, ASA, PC, PA, PET, Carbon/ Glass Fiber Reinforced Polymer Not Recommended
Monitoring Camera Low Rate Camera (up to1080P) Timelapse Supported
Filament Run Out Sensor Yes
Filament Odometry Yes
Power Loss Recover Yes
Filament Tangle Sensor Yes
Package size 546*532*320 mm
Net Weight 14.3 kg

side2_mod_top side2_mod_bottom
Back to Top