![[3D列印機] Ultimaker2-新手開箱懶人包!](http://3dmart.com.hk/cdn/shop/articles/201512021834580.jpg?v=1779423919&width=1600)
This must be the concern of many novice 3D printing enthusiasts! Don't worry! We've heard your concerns.
Allow us to proudly present: Ultimaker 2 - Novice Unboxing Guide!
From unboxing to setup, and then 3D printing your first object, clear videos with complete explanations will help you quickly overcome the beginner's learning curve!
Unboxing
Beginning Unboxing:
The Ultimaker 2 is transported in specially designed durable packaging. Please follow the steps below to unbox it correctly and ensure the packaging can be reused.
Unfasten the straps:
Unfasten the straps to remove the accessory box. Open the accessory box, and you will find a quick start guide.
Remove the styrofoam packaging:
First, you will see a spool of PLA and a sample print on the styrofoam in front of the machine. Remove them first.
Second, remove the styrofoam panels from the front and back of the machine.
Finally, remove the styrofoam panel from beneath the machine.
Caution! When moving the machine, hold the frame of the machine. Do not apply force to the belts or the print head's moving axis.
Remove the protective kit:
Use both hands to lift the print platform and remove the protective air cushion underneath.
Cut and remove the cable ties next to the print head.
Your Ultimaker 2 is now ready for use.
Contents:
The following accessories are included in the Ultimaker 2 package:
1. Power adapter and power cord
2. Spool holder
3. Glass plate
4. Filament X1
5. USB cable
6. Glue stick
7. Lubricant
8. Hex wrenches (1.5mm, 2mm, 2.5mm)
9. Calibration card
10. Sample print
11. Spare parts (heater cartridge, PT100 temperature sensor)
Assembly
Spool holder:
First, insert the upper part of the spool holder into the slot at the back of the machine, then push down the spool holder to engage the latch.
Glass plate:
The glass plate is the printing surface on which the Ultimaker 2 prints objects.
Use an Allen wrench to open the two metal clamps at the front of the print platform.
Gently slide the glass plate onto the print platform until it clicks into the two metal clamps at the back of the platform.
Finally, close the metal clamps at the front of the platform, and you're done.
Caution! The edges of the metal clamps are sharp, so it is recommended to use an Allen wrench to open them.
Power supply:
The final step of assembly is connecting the power cord. Before connecting, make sure the machine's switch is in the OFF position.
Connect one end of the power cord to a socket and the other to the machine; when connecting the plug to the machine, insert it with the flat side facing up.
Caution! The edges of the metal clamps are sharp, so it is recommended to use an Allen wrench to open them.
Calibration
Platform leveling:
The Ultimaker 2 screen will guide you step by step through leveling the print platform. It is very important that the first layer extrudes well and adheres to the print platform. If the platform is too far from the nozzle, the extruded filament will not adhere well to the platform; if the platform is too close to the nozzle, the filament will not be able to extrude from the nozzle.
Before starting the calibration, the Ultimaker 2 needs to be homed. The print head and platform will move automatically to set this. Once completed, you can proceed with the leveling according to the subsequent steps.
Height setting:
This is the first step of leveling. Rotate the knob next to the screen to move the print platform until it is about 1mm from the nozzle. The precise distance is not important, just make sure the platform is close enough to the nozzle without touching it.
Initial calibration:
Perform initial calibration using the two calibration screws at the front of the platform. Push the knob to the left to raise the platform, and vice versa to lower it. Again, aim for about 1mm between the platform and the nozzle.
Fine-tuning:
Use the calibration card for fine-tuning.
Place the calibration card between the platform and the nozzle. Adjust the calibration screws while moving the calibration card to feel the friction between the platform and the nozzle.
The nozzle will automatically select three points for you to repeat the same steps. Adjust the friction between the platform and the nozzle to be the same at all points.
Caution! When fine-tuning, do not push the platform to avoid affecting accuracy.
Loading Filament
Placing Filament:
Place the filament on the spool holder in a counter-clockwise direction.
Loading Filament:
Cut the tip of the filament into a sharp shape.
Insert the filament into the feeder motor and push with force until the filament slowly enters the Bowden tube.
Before the filament reaches the first feeder tube clamp, press the knob next to the screen to continue automatic feeding.
After pressing continue, the filament will quickly reach the print head.
After the print head heats up to the preset temperature, the filament will automatically extrude from the print head.
During this process, you may notice some clicking sounds from the feeder motor. This is a normal phenomenon when the motor encounters greater resistance, so please do not worry. You can also push the filament slightly to help the motor feed.
Caution! Do not touch the print head during heating to avoid burns.
Caution! The initial color of the extruded filament may be different from what you loaded. This may be due to residual filament from factory testing. The color will return to normal once the residual filament is completely extruded.
Printing
First Print:
After completing the print platform leveling and loading the filament, you can start your first print. Ultimaker has included several print files on the accompanying SD card; please select one to begin your first print.
After selecting a print file, the Ultimaker 2 will automatically home the print platform and print head again, and then begin heating the print head and heated bed. This process takes approximately 5 minutes.
During printing, the screen will display the printing progress and remaining time. After printing is complete, please wait for the platform to cool before removing the printed object.
TIP: To help the printed object adhere better to the platform, you can apply a thin layer of glue stick to the platform.
Article source: https://ultimaker.com/en/support/157-unboxing
Translated by: 3DMART Ltd.