【Vacuum Forming】Is Maintenance Really That Important? Mayku Multiplier Daily Maintenance Tutorial!

【Pressure Forming】Is Maintenance Really That Important? Mayku Multiplier Daily Maintenance Tutorial!

Does a pressure forming machine also need maintenance? What's the difference between regular maintenance and infrequent maintenance? How often should it be done? If you've already purchased or are interested in pressure forming, you might have these questions. For users, the most important thing is to maintain high-quality manufacturing, and that means keeping your Multiplier in optimal condition. This article details the maintenance schedule and procedures. Please note: This schedule assumes an annual usage frequency of 2,500 forming cycles.

Tip: If the usage frequency is higher, more frequent maintenance is recommended to ensure optimal forming results.
 

👉 Related Article: Create Custom Precision Models! Mayku Multiplier Unboxing Guide!


6.2.1 Weekly Inspection Tasks

Task	Action
Check the seal for dirt or residue	Gently wipe the seal with a damp cloth
Check the bed for debris or dirt	Wipe with a damp cloth, or remove the bed for thorough cleaning
Check the heaters for cracks or signs of malfunction	Do not attempt to repair yourself If there is a problem, please contact our professional technicians

 

6.2.2 Monthly Inspection Tasks
 

Task	Action
Drain the water tank	Follow the on-screen maintenance instructions in the settings menu
Check the heating temperature sensor	Gently wipe the sensor with a damp cloth or cotton swab
Clean the heat reflector	Gently wipe the reflector with a damp cloth to ensure it is clean
Check track lubrication	If the guide rails are dry, apply recommended lubricant to ensure smooth operation

 

Weekly Tasks:
 

Clean the seal

The Multiplier has a rubber seal that holds pressurized air inside the dome during forming. The seal is located on the inner edge of the forming chamber, and it's crucial to keep it clean and free of debris, as even a small amount can create a gap. If a gap occurs, an airtight seal cannot form, causing the sheet material to sag and making it difficult to close the lid. If this happens, thoroughly clean the seal and try forming again.

Gently wipe the seal in a circular motion with a damp microfiber cloth. Ensure the seal is properly seated on the dome; an airtight seal is essential for optimal performance. Wipe off any excess moisture with a clean microfiber cloth.

Deep cleaning is recommended every 40 cycles or weekly, depending on user frequency. When the seal needs cleaning, a maintenance reminder will appear on the screen. For deep cleaning, IPA and a microfiber cloth are recommended.
 

 

Clean the base plate

Equipment:

• Torx hex key
• Microfiber cloth
• Isopropyl alcohol
 

To clean the base plate, follow these steps:

1) Locate the screws holding the base plate in place.
2) Unscrew them with a hex key to remove the base plate.
3) Use a microfiber cloth and some isopropyl alcohol to clean the base plate, removing any dirt or debris.
4) After cleaning, reinstall the base plate and tighten the screws.

Handle the screws with care and avoid overtightening them during reinstallation. This process helps maintain the performance of the Mayku Multiplier, and it is recommended to clean it every 70 cycles or weekly, depending on user frequency. When the base plate needs cleaning, a maintenance reminder will appear on the screen.
 

 

Check heaters for cracks or signs of malfunction

The heaters are located inside and at the top of the dome. A flashlight is recommended for a clear view.Open the Multiplier's lid and use a flashlight to inspect the inside of the dome.Never attempt to repair any cracks yourself; if there are cracks, please contact 3DMart.

 

Monthly Tasks:

Drain the water tank

It is recommended to drain the water tank regularly to prevent moisture buildup and rust. These tanks are made of stainless steel and are rust-resistant, but if not emptied regularly, moisture can accumulate and eventually enter the Multiplier's dome.The recommended cleaning frequency is every 100 cycles or monthly, depending on user frequency.When the water tank needs draining, a maintenance reminder will appear on the screen, providing step-by-step guidance.
 

Moisture will be released from under the valve, so keep the area clean or place a tray to catch any moisture deposits. It will be loud when released, so remember to use eye and ear protection.
 

Equipment:

• Hearing protection (earmuffs)
• Eye protection
 

You can also drain the water tank without waiting for the screen to display a maintenance reminder. Here are two options:

1) Initiate water tank drainage via the control panel

• Navigate to the main menu and select maintenance
• Follow the on-screen instructions to initiate the drainage process
 

2) Manually drain the water tank

Locate the overpressure valve and pull down the ring (M). A pencil can help trigger the valve. This action will start the drainage process. Please note that pulling the ring will make a loud noise, and your hands may get wet from the water release.

Exercise caution when performing manual drainage and ensure you are prepared for the noise and potential water spray.  

Clean the temperature sensor

Equipment:

• Air gun
• Cotton swab
 

To clean the temperature sensor, follow these steps:

1) Use dry compressed air to blow away any debris or obstructions from the sensor. This will help ensure accurate temperature readings and optimal performance.

2) If there is stubborn residue or dirt on the sensor, you can use a cotton swab to gently wipe the sensor, taking care not to apply excessive force.

By regularly cleaning the temperature sensor, you can maintain its functionality and ensure accurate temperature measurements during operation.  

Clean the reflector

The reflector is located inside and at the top of the dome. A flashlight is recommended for a clear view. It is recommended to clean it every 30 cycles or monthly, depending on user frequency.
 

Open the Multiplier's lid and use a flashlight to inspect the inside of the dome. Excessive plastic dust or residue on the heaters will appear cloudy white and should be cleaned immediately.
 

Equipment:

• Flashlight
• Microfiber cloth
• Isopropyl alcohol
 

To clean the Mayku Multiplier's reflector, follow these steps:

1) Ensure the bulbs are cool and safe to touch. Let the machine sit idle for a while before cleaning.

2) Gently clean the reflector surface with a microfiber cloth and some isopropyl alcohol. The soft and lint-free nature of the microfiber cloth helps prevent scratches or damage to the reflector.

3) When cleaning, avoid direct contact with the heaters. Direct contact can cause damage or affect their performance.

1.  
2. It is recommended to keep the Multiplier's lid closed when not in use to prevent dust from entering. By regularly cleaning the reflector with a microfiber cloth, you can keep it clean and ensure efficient heat distribution during the forming process.

 

Lubricate the guide rails

If you notice that your Mayku Multiplier's guide rails are dry and making a grinding noise, they may need lubrication. Here are the recommended steps for lubricating the guide rails:

1) Use a microfiber cloth to ensure the guide rails are clean and free of any debris or dirt, and move the lid up and down a few times.

2) For this purpose, apply a small amount of lithium-based lubricant specifically designed for this to the guide rails. This lubricant will help reduce friction and eliminate grinding noises.

Important note: Avoid using dry lubricants such as PTFE powder or graphite powder with recirculating ball or roller bearings. These lubricants are suitable for sliding friction but have limited benefits for rolling friction. We recommend using Loctite synthetic grease SuperLUBE tube.

By properly lubricating the guide rails with a lithium-based lubricant, you can ensure smooth operation and optimal performance of your Mayku Multiplier during operation.We hope this maintenance guide helps you better maintain your Multiplier and ensure it runs in optimal condition!
 

---

Mayku Multiplier Desktop Pressure Former

The Mayku Multiplier Desktop Pressure Former is designed to bring industrial-grade pressure forming technology to small and medium-sized production lines, significantly improving cost-effectiveness. It offers industrial-grade results while maintaining a desktop size, making itideal for small and medium-sized businesses and independent creators to produce customized parts and molds, such as large3D printedmodels, in under a minute, achieving batch production in a short time!

• Ultra-precise industrial heat press creates high-quality parts like injection molds
Capture sub-micron details and achieve complex designs using both thick and thin materials. Produce parts with precise surface finishes that replicate sub-micron features of the template. Create isotropic parts, ensuring structural integrity and aesthetic consistency.

• Precise control achieves unparalleled forming quality
The Multiplier's automatic leveling system ensures a stable and consistent material surface during heating. This system allows for precise temperature control, enabling the material to reach forming temperature without deforming or stretching. This improves part clarity, as the sheet can safely reach higher temperatures than any other thermoforming machine for more detailed forming. The result is a reliable and precise thermoforming process suitable for a variety of applications.

• Scalable prototyping and production
Fast cycle times of two to thirty minutes, depending on the material type. Regardless of how large or how many templates you place on the bed, the forming cycle remains constant, providing you with a consistent per-part production time.

• User-friendly operation for all skill levels
The Multiplier pressure former features an intuitive user interface designed to be easy to use out of the box. This interface is designed to guide users in optimizing machine performance, ensuring consistent and reliable results, and is suitable for users with varying backgrounds and skill levels.

• Streamline your in-house workflow
The Multiplier pressure former is designed to be placed on your desktop, always within reach, allowing you to use it exactly when you need it. By controlling the prototyping and production process yourself, you eliminate delays and uncertainties associated with outsourcing. Iterate faster, accelerate your learning curve, and speed up the journey from concept to production.
 

Click here to learn more
 

---

Want to know more about Mayku products? Click "Contact Us" below!